HARD RACING.com
 

 



Pit Bull motorcycle stands were designed to be simple, rugged, and easy to use. PitBull is constantly looking for ways to improve their stands.  Racer and user feedback are often behind their  improvements.

Pit Bull  stands are made entirely from steel tubing and bar because they feel that a little too tough is better than a little too flimsy. Very high strength steels are used where needed. Rugged 4 inch wheels allow the stands to be used on rough ground. Pitbull stands are hand built and TIG welded. Zinc plating protects them from the elements and gives them their distinctive gold finish (this is the same finish used on many of the nuts and bolts on your motorcycle). Proudly made in the U.S.A.

New  For  '07-'08:
Pitbull MOBILE  Wheel/Tire Stand  - $339
_____________________________________________________________

Pitbull Jack Stands - $145/set of 2 stands
(4) Jack Stands Shown in Picture holds entire bike off the ground)

_____________________________________________________________

Pitbull   "FORWARD" One Arm Rear Stand.
PitbullNewrear.gif (26340 bytes)
- Less clutter around the Back Tire while adjusting the Chain, or Removing the Wheel.
- No more need to balance the bike by the tail section ,while installing the stand.
- Adjustable Brackets allow For Up or Down Movement, to give "more" or "less" ground clearance
   to suit your needs.  Brackets are also adjustable in and out for different swingarm width.
 (Available With Either  Spooled  OR  Standard  Brackets) 
SALE PRICE - $135    IN STOCK  

FOR THE ULTIMATE, in SOLID MOUNTING SETUP:  Use Pitbull, Forward Arm w/ "Standard Adapters"  and Gilles Chain Adjusters w/ Lifters.  Get the SAME "GP STYLE" SETUP as the Professional Teams use.

      
GILLES Swing Arm Lifters &
SUPERBIKE Chain Adjusters
 

_____________________________________________________________


Pitbull TRADITIONAL REAR STANDS  

  (Available in Spooled, Standard, or "SS" )

Pitbull Standard Rear ($126.00): IN STOCK
  • Fits virtually all chain (or belt) driven bikes with conventional swingarms except bikes with very low pipes.
  • Width is adjustable to fit swingarm widths of 10.5 in to 14.0 in. 
  • Rubber pads protect bottoms and sides of swingarm.
  • Allows rear wheel cleaning and removal and chain oiling and adjusting.

 
Pitbull Spooled Rear ($126.00): IN STOCK
  • Same as our standard rear but with spooled adapters to lift bikes with spool-equipped swingarms.
Pitbull "SS" Rear ($135.00): IN STOCK
  • Reversible Adapter... Both Standard & Spooled Setup on the same adapter.
  • Allows to lift bikes with spool-equipped swingarms as well as standard. "Best Buy"

Use as Standard or Spooled Rear


Spools ($16.00):  
  • We have 6, 8, 10 and 12mm spools.
  • 6 & 8mm spools are aluminum and are provided with attach bolts. They come in a wide variety of bright colors.
  • 10 and 12mm spools are made from high strength steel and zinc plated like our stands.


Pitbull One Armed Rear ($139.00):  
  • Very simple, very strong.
  • Fits Honda Hawk, VFR, RC 30/45, NC 30, RS 250, Ducati 748/916, Triumph T509/T595.
  • Allows rear wheel cleaning and removal and chain oiling and adjusting.


FRONT STANDS
"NEW" Standard Front Stand ($147.00):  IN STOCK 
 
  • This stand allows front wheel removal and cleaning and fork leg removal.
  • Fitting Chart shows which pins &/or adapters are needed to fit your bike.
   
  Forklift Front Stand ($135.00):
IN STOCK  
  • Sized to fit all new sport bikes with no need to adjust.
  • Forks rest on rubber pads so your bike will not get scratched.
  • Allows front wheel cleaning and removal.



 

 Pitbull BMW Stands

New!   BMW FRONT Stand ($138):  

  • Similar to our Forklift Front, this stand is tailored to fit the 2005 BMW K1200S & K1200R. Allows front wheel cleaning and removal. Use only with rear stand.

    Fits 2005 BMW K1200S and K1200R.
New!   BMW REAR Stand ($175):  

  • Rear stand for 2005 BMW K1200S and K1200R with the new single-sided swingarm. It allows rear wheel removal. The forward handle layout lets you hold the left handlebar of the bike to operate. It is space-saving and leaves no trip hazard behind the bike. The ball bearing head allows you to spin the wheel while the bike is on the stand for easy wheel cleaning.
    Fits 2005 BMW K1200S and K1200R.

 

Pitbull DUCATI STANDS

New!   One Armed Rear - Ducati 1098/MV Agusta
F0027B-000 (Stand Includes 2 Pins  40mm & 42mm)
 REVERSIBLE   ($179) 

  • For Ducati 1098 & MV Agustas with single-sided swingarms. When installed on the left side, it allows wheel removal; when installed on the right side, it allows easy sprocket removal. On left side, handle is forward; on right side handle is behind bike. It offers great leverage and stability and the ball bearing head makes it easy to spin the wheel for chain oiling. Sold complete, but pins are interchangeable to fit other bikes. Fits Ducati 1098 & MV Agusta LH and RH, On some models the 1098/MV pin will fit both sides of the bike. On other models the 1098L pin will fit the left side, and the 1098/MV pin will fit the right side. Stand is sold complete with both pins.
New!   One Armed Rear - Ducati 1098/MV Agusta ($145)F0027-000 (Stand Includes 42 mm Pin) 
OR
F0027c-000 (Stand Includes 40 mm Pin)
($145):  

  • Allows wheel removal for Ducati 1098s & MV Agustas with single-sided swingarms. It offers great leverage and stability and the ball bearing head makes it easy to spin the wheel for chain oiling. Sold complete, but pins are interchangeable to fit other bikes. Fits Ducati 1098 & MV Agusta.


 

New!
Pitbull Ducati Forklift Converter ($165.00):
  • Fits stock 996/ 916/ 748/ 1098
    (no hole through steering stem).
  • Use with Forklift Front Stand to service forks.
  • Replaceable Delrin pads (see insert) cradle lower triple clamp without scratching clamp or fender.
     
    •
  • COMBO Package price for Forklift Front
     AND Ducati Converter:      $285.00     

Forklift Front  AND  Ducati Converter
COMBO  Shown Here
New!
Ducati Standard Front ($240.00):
  • Fits stock 996/916/748 (no hole through steering stem).
  • Allows wheel removal and fork servicing.
  • Replaceable Delrin pads (see insert) cradle lower triple clamp without scratching clamp or fender.
  • Top bar for existing front stand may be purchased separately for $140.00.

New!
Ducati Delrin Pads:

  • Fits the Ducati lower triple clamp (patent pending)