For Special Offers, follow us on
Twitter
&
Facebook: Click
>>
<< to become a Fan or Friend.
You could be one of our Lucky $30 HardRacing e-GIFT CARDS PRIZE WINNERS,
Each Week..
New Parts /
Updated: 04-19-24
We update these pages often.
Be sure to hit
REFRESH on your browser, each time you check this page.
Or it may Not Show the new parts.
DYNOJET PC 6
Featuring: State of the Art Technology
New Mapping methods,
Transfer and Auxiliary Data Port for Future Add-ons.
- Control FUEL
- Control the IGNITION
- Raise Rev. Limit
- Add optional Autotune
- Add optional Quick Shifter
- Add optional LCD Display
- Fuel pump accelerator feature
OPTIONAL ACCESSORIES
AUTO TUNE & WBC2 DEVICES - for AUTOTUNE Mapping.
WIDEBAND Commander 2 (WBC2) for use with PC V
Similar to the
“Auto Tune” kit that include Wide Band O2 sensors and
control boxes. It will plug directly into the PCV and allow automatic fuel
adjustments. Auto Tune can make a map for each gear it can map each
cylinder separately for each gear if needed. (basic settings would make one
map for all gears) “Warm Up” fuel adjustment (unit reads engine temp
and allows fuel/timing adjustments based on it) Each map cell is
individually adjustable so you can specify an exact AFR value for each area
if needed. This allows the tuner/user to select specific AFR targets for
idle, cruise, and large throttle opening areas. By doing this you can
automatically tune the cruise area for best fuel economy while at the same
time achieve maximum power at wide open throttle.
If Dyno Jet does not have the exact map for your combination of parts you
simply need to choose the closest one and let the WBC2 kit do the rest.
Additional features of WBC2 over an Autotune :
Low Voltage output for o2 Sensor Signal (to wire directly into your
stock ECU)
- Output for Optional A/F Digital Gauge
WIDE BAND COMMANDER 2 AUTO TUNE KITS
Retail : $300
OUR SALE PRICE - $328.99
P.N. 15-7023
(IN
STOCK)
PLEASE NOTE:
Hard Racing is the ONLY Company currently selling this Specific
WBC2 model, which we specifically setup for the Honda Monkey to run at
13.5 A/F Ratio.
Real time fuel adjustments
Display channels real-time: RPM, TP,
map position (when using map
switch), duty cycle,
fuel change,
ignition change & wideband air/fuel
ratio- (w/WB2 or AutoTune connected)
Weather resistant for use in all
conditions
Log channels saved to internal
memory and can be viewed / analyzed
with Dynojet’s PowerCore Software
High contrast display, viewable in
direct sunlight
Dyno Jet POD-300 Display (for
use with PCV only)
Retail - $350 OUR Sale Price - $292.99
_________TOP
SELLERS ___________
Takegawa 145cc BBK w/ Cam
Fits: '22 + Grom RR / '22+ Monkey(5Speed)
Bolt on 50% - 75% more power!
Take your GROM from Stock 8HP to over 13 HP with this easy to install bolt
on 145cc
- Piston, rings, pin, clips and gasket kit
- Optional Performance Camshaft
p.n. 01-05-5458
Takegawa N20 High Performance Camshaft
Fits: '22+ Monkey(5Speed) ONLY /
22 + Grom RR
Bolt power!
Take your bike to the next level
p.n. 01-08-0191
Sale Price
- $157
OPMID
M1204 Multi Meter DASH
OPMID Multi
Meter DASH (Plug-n-Play) Fits: '19-'21
Monkey p.n. M1204 $344
Sale Price - $309.95 PRE-ORDERS
2022-24 MONKEY ONLY DOES NOT FIT '19-'21 Monkey
p.n. CH-1277
SALE PRICE -
$135.99 IN STOCK
OTB Billet Alum. Footpegs
Black anodized CNC machined billet aluminum -
- Replaceable stainless steel studs -
- Fantastic grip -
- Holes through the foot peg make it easy to clean out mud etc. -
- Lower profile and angled outside edge gives you more clearance in corners -
- Direct replacement for OEM -
Billet Aluminum Clutch Spring Plate
(PROUDLY MADE IN THE USA) Fits '22-'23 Monkey (5Speed) Only
(replaces your cheap quality Stock Cast Alum.
plate ,
Which can often Fail As shown above Left)
- Highly recommend when using Stiffer Clutch Springs -
SALE PRICE - $49.95
IN STOCK
Speedometer Correction Device (SRD) Now You can easily adjust your speedometer so it's
accurate
Easily Compensate for tire size changes, and gearing Changes
Slim Design / Simple to use
PLUG-n-PLAY
Front & Rear Together
STOCK ............................................. 29.5’ Avg. of 10
Attempts
Brembo Upgraded Calipers ........... 24.5' Avg.
of 10 Attempts
Front Brakes ONLY
STOCK ............................................ 31.5’ Avg. of 10 Attempts
Brembo Upgraded Calipers ........... 26.9' Avg.
of 10 Attempts
Rear Brakes Only
STOCK ............................................ 83.0’ Avg. of 5 Attempts
Brembo Upgraded Calipers ...........68.5' Avg.
of 5 Attempts ( Limited by Rear Tire Traction on Cold Pavement)
This was amazing. We knocked off nearly 20' with the Rear Brake upgrade
only.
Combined BOTH Upgrades it was 5' Shorter distance.
And remember, this is only going 30 mph to ZERO.
Most likely doing 40 or 50 to ZERO Stops would yield even More contrast from
STOCK vs. the Brembo Upgrades.
SMR Sex Machine Racing
6 Disc Clutch Plate Kit
Fits : 19-21 Honda Monkey
p.n. SMR-1002 Retail - $99
......
Sale Price - $73.95
IN STOCK
Fits 2022+ Monkey(5Speed)
p.n. SMR-1038
Retail - $99
......
Sale Price - $75
IN STOCK
Billet Aluminum Clutch Spring Plate
(PROUDLY MADE IN THE USA) Fits '19-'21 Honda Monkey 125
(replaces your cheap quality Stock Cast Alum.
plate ,
Which can often Fail As shown above Left)
- Highly recommend when using Stiffer Clutch Springs -
OHLINS FORK KIT
Valve Kit, Fork Springs & Billet Alum.
Fork Caps <<
(Complete Upgrade Replacement for OEM Forks)
Includes (2) SETS OF FORK Springs. (STANDARD
RATE & HD )
Fits: '22-23 Honda MONKEY ONLY
p.n. FDK112
NOTE: Hard Racing will Custom setup for your rider weight before
we ship.
Most other companies do not offer this service.
$350..... Sale Price $299 IN STOCK
p.n. 307-1452050
- Now Oil Changes are a simple Filter Cartridge Swap.
- Built in SITE GLASS for Oil Level Check
- Oil Ports for connecting Oil Cooler - Uses Readily Available
Replacement Cartridge Filter: OEM Honda p.n. 15412-HB6-003
p.n. 307-143220000
- Now Oil Changes are a simple Filter Cartridge Swap. (no more needing to remove
covers, wipe spinners, and replace gaskets)
- Eliminates Oil Spinner (less rotating Mass)
- Built in SITE GLASS for Oil Level Check (Big Plus)
- Oil Ports for connecting Oil Cooler - Uses Readily Available
Replacement Cartridge Filter: OEM Honda p.n. 15412-HB6-003
>>PLEASE NOTE, IF you plan on installing an Oil Cooler with this Clutch
Cover,
it will REQUIRE Custom Oil Lines or a LOWER MOUNT EXHAUST FOR
CLEARANCE <<
Sale Price Starts at - $299.95
IN STOCK
Available in Black or Silver
Kitaco
5 Row Super
Oil Cooler Lower the Oil Temps with this 5 Row Oil Cooler.
Made to work with Kitaco Clutch Cover
or Kitaco BBK Only
360-1300200EX Fits '19-'21 Honda Monkey 125
Sale Price - $244
IN
STOCK
Kitaco
Oil Cooler Lower the Oil Temps with this 3 Row Oil Cooler.
Made to work with Kitaco Clutch Cover - Shown ABOVE
^^
or Kitaco BBK Only
360-1300100EX Fits '19-'21 Honda Monkey 125
aRacer Mini X Complete ECU ALL NEW
Mini X(replacement for Mini5 )
'19-'21
MONKEY
Sale Price - Starting $445
'22+ MONKEY
(5
Speed)
Sale Price - Starting $445
IN STOCK >>
Watch Video for More Details <<
aRacer AF2 Professional Wideband O2 AFR Module
"ALL NEW" aRacer AF2
(replaces the old discontinued AF1)
Sale Price start at $320
>>
Watch Video
for More Details <<
IN STOCK
(fully programmable for Brightness of Running Lights and
Brake Lights
Also can program Brake Light Actuation features )
SALE PRICE - $129
IN
STOCK
>>
watch video<<
Yoshimura RS-3 Full System
Fits: '19-'24 Honda Monkey
p.n. 12130A5500
Yoshimura RS-3 SS/SS/TI full system weight: 5.5 Lbs.
vs. Stock Full system
weight : 11.2 Lbs.
That's over 50% Weight Savings
IN STOCK Sale
Price - $679
TB Parts
Performance
CAMSHAFT Great Boost of power added to the
CT125 / Grom / Monkey
p.n.
TBW1050
Sale Price - $74.99
Kitaco H-D Starter
- Improved Starting Performance
- More Torque
- OEM Fit
Highly recommend for BBK owners
p.n.
758-1432110
758-1432100
Sale Price - $129.95
IN STOCK
Finbro Ported SUPER Head 3.0 With Larger Valves
includes: LARGER 27mm / 23mm Valves (NO CAMSHAFT) Camshaft sold
Separately
This head is Compatible with : STOCK 125cc
or
Finbro 125 Flat Top
or
Takegawa 143cc
or
181cc BBK 2V Fits: '19-'21 MONKEY 125
Any installation of this head on other model BBK will most likely
require custom modifications Sale Price - $
259.95
LTD QTY IN STOCK
Chimera Air Intake Kit (Complete)
BLACK EDITION
Fits: '19-'21 Honda MONKEY 125
p.n. CH-1171
Includes KN Filter, Aluminum Intake, Silicone Coupler & Clamps
Key Benefit (This Intake will
retain your Stock IAT Sensor and Crankcase Breather Hose) ON SALE ... $129.99
IN STOCK >>
Watch Installation video<<
p.n. FDK107
NOTE: Hard Racing will Custom setup for your rider weight before we
ship.
Most other companies do not offer this service.
$350..... Sale Price $299 IN
STOCK
>>
Watch Video Installation <<
ALL NEW Ohlins Shock ( HO819)
36PRCL Spring Pre-Load
Compression Adjustable
Rebound Adjustable
Length Ride Height Adjust
Custom Setup for your rider weight.
Only 10-15 min to install.
One of the best improvements you can do for your Monkey NOTE: We custom setup the Shock for your rider weight , before
shipping. Most other companies don't do that.
USA OHLINS Products come with a Full 5 YR Warranty
Fits: '19-'23 MONKEY 125 / Monkey(5speed) Retail - $880
......
Sale Price - $899
IN STOCK >>
Watch Video Installation <<
OHLINS
FORK Kit
Installation Tools 60000-04
IN STOCK Sale Price $87
Kitaco NEO 181cc Big Bore Kit with
Forged Crank Shaft Fits: '19-'21 MONKEY 125
p.n. 212-1432850 / 212-1432810
(Retail:$1450)
On Sale $1049
IN
STOCK
This Kitaco "NEO" 181cc Big Bore Kit comes with everything you need for an
easy installation.
- Helps to minimize False Neutrals
- Needle Bearing used for best load distribution and smoother shifts
- Eases lateral stress on shift shaft
- CNC Machined Alum.
- Includes all the mount hardware
- Easy to install
- Black Anodized
Retail - $89
......
Sale Price - $59.95
>>
Watch Video Installation <<
IN STOCK
Takegawa Crank Shaft Support Bearing Takegawa Crank Shaft Support Bearing
Since the generator of Monkey 125 is mounted on the L. crankcase
cover, the direction of attachment of the flywheel is toward the
outside (the tip of the shaft) For this reason, the rotation weight increases of
the flywheel hangs outside the tip of the crankshaft,
and especially modified engine doubles the burden during acceleration and
deceleration.
This may affect the ignition timing that the generator and flywheel interfere,
in the worst case the crankshaft may be damaged.
By providing ball bearings inside the stator, this product changes the
crankshaft journal portion from 3 point support to 4 point support, and
restricts
crankshaft runout occurring in the high rpm region of the bore-up engine.
By limiting, vibration can be suppressed, and the durability of the stock
crankshaft can be enhanced.
This Support Bearing will ONLY WORK with STOCK FLYWHEEL
Takegawa Crank Shaft Support Bearing Takegawa Crank Shaft Support Bearing
Since the generator of GROM
is mounted on the L. crankcase cover, the flywheel mounting is closer
to the outside tip of the shaft. For this reason, the rotation weight of the
heavy flywheel is applied to the outside of the tip of the crankshaft,
and in an engine with improved pickup, the burden during acceleration and
deceleration is doubled.
This can cause the generator and flywheel to interfere, adversely
affecting ignition timing and, in the worst case, damaging the crankshaft.
By providing a ball bearing in the stator, this product changes the
crankshaft journal part from 2-point support to 3-point support, and
limits
the runout of the crankshaft that occurs in the high rpm range of the bore-up engine.
By limiting it, runout can be suppressed and the durability of the stock
crankshaft can be improved.
This Support Bearing will ONLY WORK with
STOCK FLYWHEEL
Fits: '22-'23 Grom RR
Sale Price $109.95
-
ALL NEW HARD RACING.com
T-SHIRTS
Dyno Jet, Brembo, Yoshimura Logo on one sleeve
And
Akrapovic, Alpinestars, Ohlins Logo on the other sleeve.
Takegawa Super Oil Pump
Fits: '19-'21 Honda Monkey 125
01-16-0063
Sale Price - $59
>>
Watch Video Installation <<
IN STOCK
_________EXHAUSTS __________
Yoshimura RS-3 Full System
Fits:
'19-'24 Honda Monkey
p.n. 12130A5500
Yoshimura RS-3 SS/SS/TI full system weight: 5.5 Lbs.
vs. Stock Full system weight : 11.2
Lbs.
That's over 50% Weight Savings
IN STOCK Sale
Price - $679
Termignoni
Slip On Stainless Can w/Carbon Fiber End Cap
Honda Monkey '19-21
Retail Price - $626 Sale
Price-$559
Termignoni FULL
Exhaust Stainless Can w/ Carbon Fiber End Cap
p.n. H16509400IIC
Honda Monkey '19-21
Retail Price - $900 Sale
Price-$759
>>Akrapovic<<
Stainless Dual Slip On
Sale Price $675
Stainless Header
Sale Price $281
Yoshimura RS-3 Slip On System
Yoshimura RS-3 SS/SS/TI
Sale Price - $519
TB Performance Exhaust
Canister options: Stainless, Matte Black, or Carbon Fiber Can
Retail is $420
Sale Price Starts at $279.00
Hindle Full Evo Megaphone Systems
'19-'21 MONKEY 125 Retail -$600
Coming soon
>> Competition Werkes Full System
Honda Monkey Exhaust <<
'19-'21 MONKEY 125 Retail -$600
Coming soon
Front & Rear Together
STOCK ............................................. 29.5’ Avg. of 10
Attempts
Brembo Upgraded Calipers ........... 24.5' Avg.
of 10 Attempts
Front Brakes ONLY
STOCK ............................................ 31.5’ Avg. of 10 Attempts
Brembo Upgraded Calipers ........... 26.9' Avg.
of 10 Attempts
Rear Brakes Only
STOCK ............................................ 83.0’ Avg. of 5 Attempts
Brembo Upgraded Calipers ...........68.5' Avg.
of 5 Attempts ( Limited by Rear Tire Traction on Cold Pavement)
This was amazing. We knocked off nearly 20' with the Rear Brake upgrade
only.
Combined BOTH Upgrades it was 5' Shorter distance.
And remember, this is only going 30 mph to ZERO.
Most likely doing 40 or 50 to ZERO Stops would yield even More contrast from
STOCK vs. the Brembo Upgrades.
Front & Rear Together
STOCK ............................................. 29.5’ Avg. of 10
Attempts
Brembo Upgraded Calipers ........... 24.5' Avg.
of 10 Attempts
Front Brakes ONLY
STOCK ............................................ 31.5’ Avg. of 10 Attempts
Brembo Upgraded Calipers ........... 26.9' Avg.
of 10 Attempts
Rear Brakes Only
STOCK ............................................ 83.0’ Avg. of 5 Attempts
Brembo Upgraded Calipers ...........68.5' Avg.
of 5 Attempts ( Limited by Rear Tire Traction on Cold Pavement)
This was amazing. We knocked off nearly 20' with the Rear Brake upgrade
only.
Combined BOTH Upgrades it was 5' Shorter distance.
And remember, this is only going 30 mph to ZERO.
Most likely doing 40 or 50 to ZERO Stops would yield even More contrast from
STOCK vs. the Brembo Upgrades.
Radial Brake Master Cylinder 14 RCS
The RCS 14mm has been designed for the rider who requires more brake
performance
and variation in brake lever feel when
compared to a stock
master cylinder.
The RCS offers flexibility to change the brake lever ratio at the turn of a
screw.
This would enable the rider to decide on the 14 x 20 option or the 14 x 18 option..
This is achieved by the use of an eccentric drive
which is turned by the simple screw mechanism
and has a color coded pivot
rod end that allows the rider at a glance to understand the current setting.
The 14mm RCS is designed for use on single rotor systems (Supermoto) or 2- piston calipers. RCS14
Sale Price:
$275 (Order this Brembo RCS on-line, and receive
FREE EXPRESS Shipping )
IN STOCK
Radial Brake Master Cylinder 15 RCS
The RCS 15mm has been designed for the rider who requires more brake
performance and variation in brake lever feel when
compared to a stock
master cylinder.
The RCS offers flexibility to change the brake lever ratio at the turn of a
screw. This would enable the rider to decide on the 15 x 20 option normally
used on the street or the 15 x 18 option which is suited to track day or
amateur racing. This option is achieved by the use of an eccentric drive
which is turned by the simple screw mechanism and has a color coded pivot
rod end that allows the rider at a glance to understand the current setting.
The 15mm RCS is designed for use on single rotor systems (Supermoto) or dual
floating 4 piston calipers. RCS15
Sale Price:
$290
(Order this Brembo RCS on-line, and receive
FREE EXPRESS Shipping )
IN STOCK
BREMBO "CORSA CORTA
RR" RCS15
Brake Mastercylinder
Sale Price:
$695 (Order this Brembo RCS on-line,
and receive FREE EXPRESS Shipping
)
Brembo Sintered Pads for Brembo
Upgrade 34mm Caliper Fits: '19-'21 MONKEY 125
Coming soon
Sale
Price:
$36.95
SBL Front Braking Disc
(with Red or
Black or Gold Carrier) Fits: '19-'21 MONKEY 125 Only $74.95 Please note: This Rotor
will NOT work with Brembo Upgrade Caliper Kitxxx
GALFER WAVE ROTORS - $109
Fits: '19-'21 MONKEY 125 (over 1/2 lb lighter then stock)
>>
Galfer Wave Rotors <<
Please note: This Rotor will NOT work with Brembo Upgrade Caliper Kit
EBC
BRAKE PADS Fits: '19-'21 MONKEY 125
$32.95 + Up
Kitaco Front Rotor - '13-19 Honda Grom/Grom SF (Non-ABS)
Available in variety of colors
"WILL NOT WORK WITH ABS"
Fits: '22 + Grom RR / '22+ Monkey(5Speed)
Bolt on 50% - 75% more power!
Take your GROM from Stock 8HP to over 13 HP with this easy to install
bolt on 145cc
- Piston, rings, pin, clips and gasket kit
- Optional Performance Camshaft
p.n. 01-05-5458
Takegawa N20 High Performance Camshaft
Fits: '22+ Monkey(5Speed) ONLY /
22 + Grom RR
Bolt power!
Take your bike to the next level
p.n. 01-08-0191
Sale Price
- $157
KOSO 170cc BBK
Includes:
• 170cc ceramic coated cylinder
• Forged piston
• Pin, Rings, Clips
• Banjo Bolts w/ crush washers
• Base gasket
• Head gasket
Sale Price-$359.95
IN STOCK
Koso Upgrade Cam Chain Tensioner Arm
Fits: 2022+ Monkey (5-speed) & 2022+ Grom RR ONLY
Sale Price - $84.99
IN STOCK
TAKEGAWA Upgraded Cam Chain Tensioner Arm
P.N. 01-14-0007 / 01-14-0011 Fits : Honda Monkey 125 '19-'21 - Improved performance
- Lighter weight Arm
- Wider Foot
- New Pivot Bushing
- C-Clip Retaining Ring for Quick Wheel replacement
Retail - $110
SALE PRICE - $87
IN
STOCK
Kitaco Crankshaft Assembly Tool
I
N STOCK
Sale Price $69.95
Kitaco
5 Row Super
Oil Cooler Lower the Oil Temps with this 5 Row Oil Cooler.
Made to work with Kitaco Clutch Cover
or Kitaco BBK Only
360-1300200EX Fits '19-'21 Honda Monkey 125
KITACO
"DOHC" 4v Valve 181cc BIG BORE KIT for Honda
'13-'20 Grom & '19-21 Monkey
p.n.
215-1432900
$3299.Sale Price - $2499
LTD. QTY IN STOCK
TB Parts
Performance
CAMSHAFT Great Boost of power added to the
CT125 / Grom / Monkey
p.n.
TBW1050
Sale Price - $74.99
Takegawa Clutch Cover
p.n.
02-01-0150
- Now Oil Changes are a simple Filter Cartridge Swap.
(no more needing to remove covers, wipe spinners, and replace gaskets)
- Eliminates Oil Spinner (less rotating Mass) - Saves 2.5 lbs of mass from crank shaft - Built in SITE GLASS for Oil Level Check (Big Plus)
- Oil Ports for connecting Oil Cooler
- Removable Access Panel to check Clutch Plates (Without having to remove
Entire Cover)
Uses Readily Available Replacement Cartridge
Filter: OEM Honda p.n. 15412-HB6-003
Takegawa Clutch
Cover KIT ........
Sale Price - $359
>>WILL NOT WORK WITH STOCK EXHAUST : REQUIRES A LOWER MOUNT EXHAUST FOR
CLEARANCE<< (IN
STOCK)
Fits : '19-'21 Monkey & '13-'20 GROM / GROM SF
>>
Watch Video Installation <<
Koso Upgraded Cam Chain Tensioner Arm
Fits: 2019-2021 Monkey & 2013-2020 Groms ONLY
Retail - $110
SALE PRICE - $87
IN STOCK
p.n. 307-143220000
- Now Oil Changes are a simple Filter Cartridge Swap. (no more needing to remove
covers, wipe spinners, and replace gaskets)
- Eliminates Oil Spinner (less rotating Mass)
- Built in SITE GLASS for Oil Level Check (Big Plus)
- Oil Ports for connecting Oil Cooler - Uses Readily Available
Replacement Cartridge Filter: OEM Honda p.n. 15412-HB6-003
>>PLEASE NOTE, IF you plan on installing an Oil Cooler with this Clutch
Cover,
it will REQUIRE Custom Oil Lines or a LOWER MOUNT EXHAUST FOR
CLEARANCE <<
Sale Price Starts at - $299.95
Available in Black or Silver
p.n. 307-1452050
- Now Oil Changes are a simple Filter Cartridge Swap.
- Built in SITE GLASS for Oil Level Check
- Oil Ports for connecting Oil Cooler - Uses Readily Available
Replacement Cartridge Filter: OEM Honda p.n. 15412-HB6-003
Lower the Oil Temps with this 3 Row Oil Cooler.
Made to work with Kitaco Clutch Cover - Shown ABOVE ^^
or Kitaco BBK Only
360-1300100EX Fits '19-'21 Honda Monkey 125
Key features:
Takegawa's 181cc 4 Valve Superhead kit offers never before seen power and
delivery from a single cam cylinder head.
All Takegawa's technology and racing heritage has now been power packed into
this SOHC camshaft 4V head,
perfectly matched for the 181cc supplied bore kit.
ALL NEW Takegawa 181cc 4v Superhead
GEN2
with (5 AXIS CNC Machined INTAKE Port
Matched Head )
DYNO >> Takegawa 181cc 4v Superhead
GEN 2 with (5 AXIS Port
Matching Machined Head )
P.N.
01-05-0130 / 01-05-0165
Same details as standard 4v 181cc BBK..... except this one
comes with a 5 AXIS Machined head INTAKE PORTS Kit Includes:
- 181cc Takegawa Big Bore cylinder
- 181cc 4 valve piston kit
- 4 Valve Superhead with forged aluminum roller rockers
with (5 AXIS INTAKE Port
Matching Machined Head )
- Dual 25mm intake valves
- Dual 21.5mm exhaust valves
- Auto decompression Takegawa High Performance camshaft
- Piston rings, pin, clips and gasket kit
- NO Fuel Controller included
(Retail:$1880)
-
SALE PRICE Only - $1559
p.n.
01-05-0130 / 01-05-0165 (5 AXIS CNC Machined Head INTAKE Port
Matching )
Takegawa 143 2v BBK w/ Cam
Takegawa 181 2v BBK w/ Cam Takegawa Big Bore
Performance Kit Bolt on 50% - 75% more power! Take your GROM from Stock 8HP to over 12HP with this easy to install
bolt on 143cc
or Get even MORE power and Torque with 181cc Big Bore kits.
This complete kit comes with everything you need for an easy installation.
- 143cc or 181cc Big Bore cylinder
- Piston, rings, pin, clips and gasket kit
- Performance Camshaft >>
BIG BORE PERFORMANCE KITS
<<
IN STOCK
>>
watch Installation video Part 1<<
IN STOCK
Bolt on 50% - 75% more power! Take your Monkey from Stock 8HP to over 12HP with this easy to install
bolt on 143cc
or Get even MORE power and Torque with 181cc Big Bore kits.
This complete kit comes with everything you need for an easy installation.
- 143cc or 181cc Big Bore cylinder
- Piston, rings, pin, clips and gasket kit
- Performance Camshaft >>
BIG BORE PERFORMANCE KITS
<<
>>
watch Installation video Part 1<<
Kitaco NEO 181cc Big Bore Kit with
Forged Crank Shaft Fits:
'19-'21 MONKEY 125
p.n. 212-1432850 / 212-1432810
(Retail:$1450)
On Sale $1049
IN
STOCK
This Kitaco "NEO" 181cc Big Bore Kit comes with everything you need for an
easy installation.
P.N.
07-05-0041 / 07-05-0026
Takegawa Oil Catch Can
Retail $250
- Sale Price $199
Coming soon
Takegawa Oil Cooler
p.n. 07-07-0231 / 07-07-0318
For use with Takegawa 4v Super Head BBK ONLY Sale Price - $289
IN STOCK
Koso 61mm Forged 4v Piston Kit
for 170cc 4V BBK
Sale Price-$124.95
Koso 61mm Forged Piston Kit
for 170 cc 2 valve BBK
Sale Price-$84.95
Finbro Ported SUPER Head 3.0 With Larger Valves
includes: LARGER 27mm / 23mm Valves (NO CAMSHAFT) Camshaft sold
Separately
This head is Compatible with : STOCK 125cc
or
Finbro 125 Flat Top
or
Takegawa 143cc
or
181cc BBK 2V Fits: '19-'21 MONKEY 125
Any installation of this head on other model BBK will most likely
require custom modifications
Sale Price - $259
IN STOCK
Finbro 125cc High Compression Flat Top Piston
- '19-'21 HONDA Monkey 125
For STOCK BORE
c/r 11.4 : 1
Includes: 125cc piston, rings,
pin, clips Fits: '19-'21 MONKEY 125 Sale Price - $109
IN STOCK
See Our Product Video >>
FINBRO <<
KOSO Performance 34mm Throttle Body
• Control the amount of air flowing to the engine's combustion chamber
• Combining throttle body with Optional Intake manifold will allow a better
air/fuel mixture for quicker throttle response
• To be used Only with Big Bore Kits
Fits: 2019-2021 MONKEY 125 ONLY
Sale Price - $119
KOSO Performance 28mm Throttle Body
Fits: 2022+ Monkey (5-speed) & 2022+ Grom RR ONLY
• Control the amount of air flowing to the engine's combustion chamber
• Combined with the Koso Intake Manifold (sold separately)
will allow a better
air/fuel mixture for quicker throttle response
p.n. DY640000
Sale Price - $139.99
KOSO Performance
Intake Manifold
Fits: 2022+ Monkey (5-speed) & 2022+ Grom RR ONLY
• Control the amount of air flowing to the engine's combustion chamber
• Combined with the Koso 28mm Throttle body (sold separately)
will allow a better
air/fuel mixture for quicker throttle response
p.n.
DP640000
Sale Price - $72.95
KOSO 4V HEAD ONLY + PISTON
This is ideal engine part to complete the Koso Big Bore kit. Because of
its unique 4 valve design, the air flow and performance are increased. This new
designed head is the perfect addition for those who desire more power and
torque. The 4 Valve Cylinder Head Kit features a forged piston, stainless steel
24 mm intake valves and 20 mm exhaust valves. Feel the speed!
Sale Price - $679
IN STOCK
Takegawa Crank Shaft Support Bearing Takegawa Crank Shaft Support Bearing
Since the generator of
Monkey · is mounted
on the L. crankcase cover, the direction of attachment of the flywheel is toward
the
outside (the tip of the shaft) For this reason, the rotation weight increases of
the flywheel hangs outside the tip of the crankshaft,
and especially modified engine doubles the burden during acceleration and
deceleration.
This may affect the ignition timing that the generator and flywheel interfere,
in the worst case the crankshaft may be damaged.
By providing ball bearings inside the stator, this product changes the
crankshaft journal portion from 3 point support to 4 point support, and
restricts
crankshaft runout occurring in the high rpm region of the bore-up engine.
By limiting, vibration can be suppressed, and the durability of the stock
crankshaft can be enhanced. This Support Bearing will ONLY WORK with
STOCK FLYWHEEL
Takegawa Crank Shaft Support Bearing Takegawa Crank Shaft Support Bearing
Since the generator of GROM
is mounted on the L. crankcase cover, the flywheel mounting is closer
to the outside tip of the shaft. For this reason, the rotation weight of the
heavy flywheel is applied to the outside of the tip of the crankshaft,
and in an engine with improved pickup, the burden during acceleration and
deceleration is doubled.
This can cause the generator and flywheel to interfere, adversely
affecting ignition timing and, in the worst case, damaging the crankshaft.
By providing a ball bearing in the stator, this product changes the
crankshaft journal part from 2-point support to 3-point support, and
limits
the runout of the crankshaft that occurs in the high rpm range of the bore-up engine.
By limiting it, runout can be suppressed and the durability of the stock
crankshaft can be improved.
This Support Bearing will ONLY WORK with
STOCK FLYWHEEL
Fits: '22+ Monkey 5-speed
Sale Price $109.95p.n. 01-10-0149
Scotts STAINLESS OIL FILTER
For use with KITACO CLUTCH COVER ONLY. $119
SALE PRICE : $89.95
KITACO
DOHC 181cc REPLACEMENT PISTON KIT
Includes: 181cc FORGED PISTON
Rings, Clips, Pins, and Gaskets
Sale Price - $179
KITACO
DOHC CYLINDER HEAD ASSEMBLY
Includes
Kitaco
Head, Valves,Springs,Retainers,Keeper Sale Price - $1895
Bolt on 90-110% more power! Take your Monkey from Stock 8HP to over 17 HP with this easy to install
bolt on 183cc Big Bore kits.
This complete kit comes with everything you need for an easy installation.
- 183cc Big Bore cylinder
- UPGRADED JE FORGED Alum. 183cc High
Compression Piston ,
Piston Rings, pin, clips and gasket kit
- New Complete Head, with Oversized Ports
- New Oversized Valves 31mm / 26mm
- New Fuel Injector
- New Performance Camshaft - New Overbored Inlet
- New Overbored Throttle Body
- New Overbored Insulator
(Complete Upgrade Replacement for OEM Forks)
Fits: '19-'21 MONKEY 125
p.n. FDK107
NOTE: Hard Racing will Custom setup for your rider weight before we
ship.
Most other companies do not offer this service.
$350.....
Sale Price $299
IN STOCK
>>
Watch Video Installation <<
OHLINS FORK KIT
Valve Kit, Fork Springs & Billet Alum.
Fork Caps <<
(Complete Upgrade Replacement for OEM Forks)
Includes (2) SETS OF FORK Springs. (STANDARD
RATE & HD )
Fits: '22-23 Honda MONKEY ONLY
p.n. FDK112
NOTE: Hard Racing will Custom setup for your rider weight before
we ship.
Most other companies do not offer this service.
$350..... Sale Price $2
OHLINS FORK Kit
Installation Tools
60000-04
(Required to install Fork Kits, or Swap Springs or service work on
Monkey
Forks) Sale Price $87
IN STOCK
ALL NEW
Ohlins Shock ( HO819)
36PRCL Spring Pre-Load
Compression Adjustable
Rebound Adjustable
Length Ride Height Adjust
Custom Setup for your rider weight.
Only 10-15 min to install.
One of the best improvements you can do for you Grom. NOTE: We custom setup the Shock for your rider weight , before
shipping. Most other companies don't do that.
USA OHLINS Products come with a Full 5 YR Warranty
Fits:
'19-'21 MONKEY 125
Sale Price - $75
(Upgrade Replacement for OEM Forks)
IN STOCK
<<
Adj Length Ride Height
>>
JRI
Shock <<
All JRI Shocks
Custom setup for Rider
And include Length Ride Height
Single Adjustable
Retail $955 -
CALL or Email FOR PRICING Double Adjustable
Retail $1195
-
Call or Email For Pricing
ALL
Monkey
JRI Shocks have Adjustable Length Ride Height
RACE TECH FORK SPRINGS - for OEM Forks
Race Tech manufactures precision high performance springs that have
a high stiffness to mass ration.
In other words; Race Tech Fork springs are lightweight for the their
partifuclar rate.
This requires the finest materials and processing.
Race Tech OEM Replacement Fork Springs -
$135
Race Techs original bolt-on fork valving system
for cartridge forks
Triples the flow area by putting valving control on the shim stack
instead of the overly restricted stock piston
Outstanding tunability, improved control, traction, plushness and
bottoming resistance
Includes complete instructions, Gold Valve pistons, valving charts, and valving shims
Race Tech Gold Valve Fork
COMBO Kit
for OEM FORKS -
$279
(Standard Type 1 Compression Kit Plus Rebound Gold Valve)
(Fork Springs sold separately)
MOTION PRO ** ALL NEW** Rev3 THROTTLE KIT
Kit includes:
-Rev3™ throttle assembly with throttle tube
-Motion Pro Rev3™ black vinyl cables specifically designed for your bike
-Street/Road Race kits include Motion Pro RoadControl™ grips
-Standard interchangeable reels: 35mm, 40 mm, 45 mm, 50 mm
-Cam reel (Sportbike kits include Street/Road Race cam reel)
SALE PRICE - $159 (requires
start/stop switch)
GPR STEERING STABILIZER
Please
note, Stabilizer kit includes Risers & ONLY fits up to Aftermarket 1&1/8"
bars
TYGA Performance
License Plate Frame Carbon
>>SPECIAL ORDER ONLY<<
BPCC-6002
Only $78.33
WoodCraft Sprocket
Cover Left Side
Sale Price $66.49
____________ LIGHTING ___________
Direct Fit Sport Bike & Motorcycle H4,
H7, H11, 9005, 9006
LED Headlight Bulb
Retail Price - $52 Sale
Price-$38.99-46.99
CLEAR TAIL LIGHT w/ INTEGRATED SIGNALS
OEM FIT
(fully programmable for Brightness of Running Lights and
Brake Lights
Also can program Brake Light Actuation features )
Fits:
'19-'23 MONKEY 125
SALE PRICE - $129
>>
watch video<<
IN
STOCK
>>
watch video << Comp. Werkes Clear L.E.D. Tail Light
w/ Integrated Turn Signals
Clear / Red / Smoke
Fits:
'19-'23 MONKEY 125
Coming soon
SALE PRICE - $95
_____
Fender
Eliminator Kits & Undertails
_____
Honda Monkey 125 '19-'24
Yoshimura Fender
Eliminator Kit
Part # 070BG121300
SALE PRICE -
$125
IN STOCK
Honda Monkey
Driven Fender
Eliminator Kit with Turn Indicators
SALE PRICE
- $
IN
STOCK
Competition Werkes Fender Eliminator Kit Monkey Fender
Eliminator Kit
Rear mounted
Fender Eliminator Kit. Comes with new Short Stalk Turn signals and Tag light.
1H125 - $130.95
$105.95
Coming Soon or
$89.95
(without Turn Signals)
Monkey Two Brothers Fender
Eliminator Kit
click below to see detailed instructions
>>
<<
SALE PRICE
- Coming Soon
Monkey TARGA Fender
Eliminator Kit
(designed for bikes with Integrated Tailight - SOLD SEPARATELY)
SALE PRICE
- Coming Soon
_________Rear Sets ___________
DRIVEN REAR SETS
DRIVEN Racing TT Rearsets
>>
DRIVEN REAR SETS
<<
Retail - $. ...
Sale Price - $ High grade hardware / Adjustable folding toepegs
Standard/reverse shift pattern
4 different mounting positions up to 18mm up and 18mm back from new "0"
positon
New Lightweight TT design /
Made in USA
'19-'21 MONKEY 125
Available in Black, Blue, Gold, Silver, Red and in
Large or Small
$27.89
IN
STOCK
OTB Billet Alum. Footpegs
Black anodized CNC machined billet aluminum -
- Replaceable stainless steel studs -
- Fantastic grip -
- Holes through the foot peg make it easy to clean out mud etc. -
- Lower profile and angled outside edge gives you more clearance in corners -
- Direct replacement for OEM -
Fits: '19-'21 MONKEY 125
Sale Price .... $51
IN
STOCK
________ELECTRICAL
& FUEL _________
aRacer Mini X Complete ECU ALL NEW
Mini X( replacement for Mini5 )
'19-'21
MONKEY
Sale Price - Starting $445
'22-'23 MONKEY
(5
Speed)
Sale Price - Starting $445
IN STOCK >>
Watch Video for More Details <<
aRacer SUPER X Complete ECU
SUPER X
for '19-'21
MONKEY
Sale Price - Starting $795 IN STOCK
SUPER X
'22-'23 MONKEY
(5
Speed)Sale Price -
$795
(IN
STOCK)
DEVICE FEATURES:
-Flash ECU via vehicle diagnostic connector, no need to open or remove ECU from
the vehicle
-Read original tune via diagnostic connector – allows you to restore ECU at
anytime
-Display and/or log vehicle data channels in real-time
-“Hindsight” feature captures the last 2 minutes of data with the touch of a
button
-Weather resistant for use in all conditions
PERFORMANCE TUNE FEATURES:
-Support for popular aftermarket performance parts
-Fueling revised for maximum power and torque
-Spark timing optimized for pump or race gas
-Rev & speed limits raised
-Torque limiting functions reduced or eliminated
-Revised drive-by-wire throttle profiles
p.n. PV3-16-02
Sale Price - $451.99
Dyno Jet Wide
Band CX - WBCX SINGLE CHANNEL AFR KIT FOR HONDA
( FOR USE WITH PV3 )
The Wideband CX is a plug-and-play kit with no extra wires or cabling like
other sensors on the market.
Maximize your Honda motorcycle’s power and take control of your air/fuel
ratio with the Wideband CX,
perfectly paired with our best-selling Power Vision.
Specs:
Integrates AFR data from the O2 sensor with the OEM databus
Ensures real-time O2 AFR accuracy and avoids single offset issues
Sale Price - $432.99
The SENA 50R, 50S, 30K,20S, 10S, 10C Headsets are a State-of-the-art Motorcycle & Powersports Bluetooth®
communication system.
The unit provides a sleek and aerodynamic design that offers a versatile jog
dial that maximizes
the ease of use for riders.
Great Range, excellent sound quality.
- Long Lasting Battery life
- Listen to your music
- Answer or make Phone calls
- Water Resistant
- Easy to setup and use right out of the box >>
SENA
Communication System <<
Speedometer Correction Device (SRD) Now You can easily adjust your speedometer so it's
accurate
Easily Compensate for tire size changes, and gearing Changes
Slim Design / Simple to use
PLUG-n-PLAY
DYNOJET PC 6
Featuring: State of the Art Technology
New Mapping methods,
Transfer and Auxiliary Data Port for Future Add-ons.
- Control FUEL
- Control the IGNITION
- Raise Rev. Limit
- Add optional Autotune
- Add optional Quick Shifter
- Add optional LCD Display
- Fuel pump accelerator feature
OPTIONAL ACCESSORIES
AUTO TUNE & WBC2 DEVICES - for AUTOTUNE Mapping.
>>
Watch Video Installation <<
WIDEBAND Commander 2 (WBC2) for use with PC V
Similar to the
“Auto Tune” kit that include Wide Band O2 sensors and
control boxes. It will plug directly into the PCV and allow automatic fuel
adjustments. Auto Tune can make a map for each gear it can map each
cylinder separately for each gear if needed. (basic settings would make one
map for all gears) “Warm Up” fuel adjustment (unit reads engine temp
and allows fuel/timing adjustments based on it) Each map cell is
individually adjustable so you can specify an exact AFR value for each area
if needed. This allows the tuner/user to select specific AFR targets for
idle, cruise, and large throttle opening areas. By doing this you can
automatically tune the cruise area for best fuel economy while at the same
time achieve maximum power at wide open throttle.
If Dyno Jet does not have the exact map for your combination of parts you
simply need to choose the closest one and let the WBC2 kit do the rest.
Additional features of WBC2 over an Autotune :
Low Voltage output for o2 Sensor Signal (to wire directly into your
stock ECU)
- Output for Optional A/F Digital Gauge
Fits:
'19-'21 MONKEY 125 WIDE BAND COMMADNER 2 AUTO TUNE KITS
Retail : $280
OUR SALE PRICE - $399.99
IN STOCK
Quick Shifters
Click
>>
The Dynojet Quick Shifter Sensors allow
"full throttle, clutch- less" upshifts. These high quality sensors
provide fast, accurate and reliable shifting in conjunction with the Power
Commander. Sensors are attached to the gear linkage and connect into the
Power Commander expansion port. All sensors include a Software utility which
allows the user to adjust the "Kill Time" and "Minimum RPM Shift Point"
within the Power Commander Control Center Software. "Please note these
are
NOT Power Shifters. They do
NOT shift for you. They
allow "full throttle, clutch- less" upshifts, by cutting the Fuel
or Spark for a split second as you start to shift
with your foot..
Fits:
'19-'21 MONKEY 125
Coming soon
Dyno Jet PC V Quick
Shifter:
ON SALE - (
)
Inline shifters requires Aftermarket Rear Sets that use a Full Length Shift Rod
We also have a kit that works with STOCK Foot Controls To Place an order
or More Information >>
DynoJet
Quick Shifters <<
For more information, please refer to the guide below: Linkage
Adapters ONLY Sold w/ Quick Shifters.(Not sold
Separately)
IN
STOCK
Real time fuel adjustments
Display channels real-time: RPM, TP,
map position (when using map
switch), duty cycle,
fuel change,
ignition change & wideband air/fuel
ratio- (w/WB2 or AutoTune connected)
Weather resistant for use in all
conditions
Log channels saved to internal
memory and can be viewed / analyzed
with Dynojet’s PowerCore Software
High contrast display, viewable in
direct sunlight
Dyno Jet POD-300 Display (for
use with PCV only)
Retail - $350 OUR Sale Price - $292.99
IN
STOCK
PCX150 Injector 16450-KZY-701
Sale Price - $49
IN
STOCK
'19-'21 MONKEY 125
Starting at only - $159
IN
STOCK
For Headlights & Tail Lights & Turn Signals
- Please scroll Up to
- LIGHTING -
IN
STOCK
Koso RX-3 TFT Multifunction Universal Gauge BA071000
Features:
Five Changeable Colors Backlight /Gear Indicator /RPM Shift Light/Speed
/Odometer /Trip Meter /Tachometer /Temperature (over temp
warning/effective temp range)/
Voltmeter /Fuel Meter and More..
Fits: '13-'20 Grom / '19-'21 Monkey
Sale Price -
$529.99
ALL NEW OPMID
Version 2.0 Gen2
Digital Engine Temperature Gauge w/ Volt Meter Fits: Honda '19-21 MONKEY /
13-'20
GROM
M1011 / M1013 Measures the Temperature of your Motor/Head
Uses OEM Head Temp Sensor
Also Measures Voltage
Displays Fahrenheit or Celsius
Programmable Warning for Max Temp
Programmable Warning for Min Voltage
Super Slim Design Plug-n-Play
VERSION 2.0
Gen2
NEW UPDATES
1. "ALL NEW " Touchscreen ( Press and hold for 3 seconds to release screen lock )
2.Brightness up of 7 segment LED.
( High brightness Green LED is more expensive than Blue LED )
3. "ALL NEW " housing design
**
Takegawa
Oil Hole Plug (p.n.
00-02-0391)
( For
use when Using ANY Oil Cooler WITH Takegawa Clutch Cover ) $9.99
** This
Oil Hole Plug is REQUIRED in order to Run an ANY Oil Cooler with
the Takegawa Clutch Cover
**
Takegawa
Thermostat Unit (p.n.
02-01-5052)
(
REQUIRED when Using ANY Oil Cooler WITH Takegawa Clutch Cover ) $54.99
** If you
are already running a Takegawa Oil Hole Plug, the Thermo Unit NOT
**
Takegawa
Oil Filler Cap w/ BREATHER (p.n.
07-06-0001)
(
** REQUIRED when Adding ANY Oil Catch Can WITH Takegawa Clutch Cover ) $39.99
Takegawa Clutch Cover
p.n.
02-01-0150
- Now Oil Changes are a simple Filter Cartridge Swap.
(no more needing to remove covers, wipe spinners, and replace gaskets)
- Eliminates Oil Spinner (less rotating Mass) - Saves 2.5 lbs of mass from crank shaft - Built in SITE GLASS for Oil Level Check (Big Plus)
- Oil Ports for connecting Oil Cooler
- Removable Access Panel to check Clutch Plates (Without having to remove
Entire Cover)
Uses Readily Available Replacement Cartridge
Filter: OEM Honda p.n. 15412-HB6-003
Takegawa Clutch
Cover KIT ........
Sale Price - $359
>>WILL NOT WORK WITH STOCK EXHAUST : REQUIRES A LOWER MOUNT EXHAUST FOR
CLEARANCE<< (IN
STOCK)
Fits : '19-'21 Monkey & '13-'20 GROM / GROM SF
>>
Watch Video Installation <<
Sample photo shows Silver, but Final product will be BLACK Anodized
EXACT PRODUCT PHOTO >>
HardRacing SHIFT
SHAFT SUPPORT BRACKET - Helps to minimize False Neutrals
- Needle Bearing used for best load distribution and smoother shifts
- Eases lateral stress on shift shaft
- CNC Machined Alum.
- Includes all the mount hardware
- Easy to install
- Black Anodized
Retail - $66
......
Sale Price - $59.95
Billet Aluminum Clutch Spring Plate
(PROUDLY MADE IN THE USA) Fits '19-'21 Honda Monkey 125
(replaces your cheap quality Stock Cast Alum.
plate ,
Which can often Fail As shown above Left)
- Highly recommend when using Stiffer Clutch Springs -
SALE PRICE - $49.95
Totally customize how much spring
pressure you want.
Use all 6 for Max. Pressure, or use 4 Kitaco + 2 Stock, or use
2 Kitaco
+ 4 Stock ... to get just the perfect feel you
want.
Sale Price - $28.00
IN
STOCK
>>
Watch Video Installation <<
Fly Wheel/Clutch Holding Tool
Makes Cleaning your Oil Spinner and Any Clutch work 10 x easier.
No more trying to figure out how to keep the Oil Spinner or Clutch Basket
from Rotating
Sale Price - $37.95
IN
STOCK
>>
Watch Video Installation <<
Flywheel/Stator
Puller Tool 30MM
Makes Pulling the Flywheel/Stator on your Honda Monkey 10 x easier
Sale Price - $29.95
IN
STOCK
Barnett - Complete Clutch
Kit Kit Includes : Kevlar Fiber Plates, Steel Plates,
and H-D Springs
Sale Price - $119
IN
STOCK
Fits:
What does a Slipper Clutch Do ?
During rapid downshifting, a slipper clutch temporarily
reduces the amount of friction in a clutch,
which
disconnects (to a degree) the final drive and transmission
of a motorcycle.
The result is a decrease in engine braking
and an increase in rear wheel freewheeling.
Translation...... Less Rear Wheel Hop when you dive into a Corner and drop
the clutch. = More Control
Must use with STOCK OEM Clutch Plates and Springs.
Takegawa Slipper Clutch : Sale Price - $179
Fits:
'19-'21 MONKEY 125
Click for More Details >>
5 SPEED <<
DISCONTINUED
>>
Billet Aluminum Clutch and Brake Levers ( Shorty
)
<<
Starting @ $97
IN
STOCK
Fits:
'19-'20 MONKEY 125
p.n. 307-143220000
- Now Oil Changes are a simple Filter Cartridge Swap. (no more needing to remove
covers, wipe spinners, and replace gaskets)
- Eliminates Oil Spinner (less rotating Mass)
- Built in SITE GLASS for Oil Level Check (Big Plus)
- Oil Ports for connecting Oil Cooler - Uses Readily Available
Replacement Cartridge Filter: OEM Honda p.n. 15412-HB6-003
>>PLEASE NOTE, IF you plan on installing an Oil Cooler with this Clutch
Cover,
it will REQUIRE Custom Oil Lines or a LOWER MOUNT EXHAUST FOR
CLEARANCE <<
Sale Price Starts at - $299.95
Available in Black or Silver
2022-24 MONKEY ONLY
DOES NOT FIT '19-'21 Monkey
p.n. CH-1277
SALE PRICE -
$135.99
IN STOCK
Chimera Air Intake Kit
(Complete)
Black Edition Fits: '19-'21 MONKEY 125
p.n. CH-1171
Includes KN Filter, Aluminum Intake, Silicone Coupler & Clamps Key Benefit : MORE POWER
(This Intake will retain your Stock IAT Sensor and Crankcase Breather Hose)
ON SALE ... $129.99 IN STOCK
>>
Watch Installation video<<
Dunlop Scootsmart 2 Tires
Key features of the new Scootsmart include:
-Technologies derived from Dunlop’s performance touring tires.
-Proven performance tread pattern inspired by Dunlop’s performance
touring tires.
-Enhanced responsiveness and handling when compared with the SX01
scooter tire it replaces.
-Fits Honda Monkey and other large engine-displacement scooters. Sold As Set
Retail: $202
Set Sale Price Starts
At: $169
MAXXIS
Knobby Tread -
Set
Knobby tread pattern designed
to excel in both on-road and off -road riding conditions
Set Size: 130/70-12 ,
120/70-12
Sale Price as a
SET -
$128
IN STOCK
Fits:
'19-'21 MONKEY 125
Coming soon
Sport Bike Lites - Billet Raptor Frame Sliders
Available in Black, Red, Yellow or White
Sale Price Starting at $79.99
WoodCraft Axle Slider Kit
(Front or Rear)
Fits:
'19-'23 MONKEY 125
Sale Price Starts @ $63
IN
STOCK
YOSHIMURA Bar Ends
Fits: '19-'23 MONKEY 125 Sale Price .... $43.95
STOMPGRIP Traction Pads Sale Price .... $63.99
Coming Soon
______MISCELLANEOUS
& SWAG_______
ALL NEW HARD RACING.com
T-SHIRTS
Dyno Jet, Brembo, Yoshimura Logo on one sleeve
And
Akrapovic, Alpinestars, Ohlins Logo on the other sleeve.
Real time fuel adjustments
Display channels real-time: RPM, TP,
map position (when using map
switch), duty cycle,
fuel change,
ignition change & wideband air/fuel
ratio- (w/WB2 or AutoTune connected)
Weather resistant for use in all
conditions
Log channels saved to internal
memory and can be viewed / analyzed
with Dynojet’s PowerCore Software
High contrast display, viewable in
direct sunlight
Dyno Jet POD-300 Display (for
use with PCV only)
Retail - $350 OUR Sale Price - $292.99
Features:
Five Changeable Colors Backlight /Gear Indicator /RPM Shift Light/Speed
/Odometer /Trip Meter /Tachometer /Temperature (over temp
warning/effective temp range)/
Voltmeter /Fuel Meter and More..
Fits: '13-'20 Grom / '19-'21 Monkey
Sale Price -
$529.99
ALL NEW OPMID
Version 2.0 Gen2
Digital Engine Temperature Gauge w/ Volt Meter
Fits:
Honda '19-21 MONKEY /
13-'20
GROM
M1011 / M1013 Measures the Temperature of your Motor/Head
Uses OEM Head Temp Sensor
Also Measures Voltage
Displays Fahrenheit or Celsius
Programmable Warning for Max Temp
Programmable Warning for Min Voltage
Super Slim Design Plug-n-Play
VERSION 2.0
Gen2
NEW UPDATES
1. "ALL NEW " Touchscreen ( Press and hold for 3 seconds to release screen lock )
2.Brightness up of 7 segment LED.
( High brightness Green LED is more expensive than Blue LED )
3. "ALL NEW " housing design
GPS (Satellite) Technology.
NO Transponder Need. Imagine, No More worrying about setup .Transponders on the
side of the track each time you go out, or
Each time you come in. Those days are done.
Just go out on the track, Set the Start/Finish Line and the GPS (Satellites) Does it all for you. Current Speed, Lap Times, RPM;s, Max Speed, Fastest lap.....and
much more.
You can even Save each track, in memory. NO Wire Splicing, or
taping necessary.
This Unit
Easily transfers from bike to bike. Or you can put it in your car, or
truck, or SUV.
Very handy device.
TYPE R - With TRACK MAPPING. Downloaded to your
PC or Laptopp
Escort / Passport iQ Radar Detector / Laser Detector /
GPS Navigation,
All in one Device
click >>
Passport iQ
<<
_________
WHEELS ___________
BST Carbon Fiber Wheels
** Please Note: These do have the
MONKEY
Logo on the wheel hub if you order the Monkey Wheels**
Wheel pricing Starts at - $785
Usually IN STOCK
_________
RACE PARTS __________
QUICK SHIFTERS
Click
>>
The Dynojet Quick Shifter Sensors allow
"full throttle, clutch- less" upshifts. These high quality sensors
provide fast, accurate and reliable shifting in conjunction with the Power
Commander. Sensors are attached to the gear linkage and connect into the
Power Commander expansion port. All sensors include a Software utility which
allows the user to adjust the "Kill Time" and "Minimum RPM Shift Point"
within the Power Commander Control Center Software. "Please note these
are
NOT Power Shifters. They do
NOT shift for you. They
allow "full throttle, clutch- less" upshifts, by cutting the Fuel
or Spark for a split second as you start to shift
with your foot..
Dyno Jet PC V Quick
Shifter:
ON SALE - (
)
Inline shifters requires Aftermarket Rear Sets that use a Full Length Shift Rod
We also have a kit that works with STOCK Foot Controls To Place an order
or More Information >>
DynoJet
Quick Shifters <<
CHECK YOUR BIKES SPECIAL PAGE OFTEN....... WE ARE ALWAYS
UPDATING AS SOON AS NEW PARTS BECOME AVAILABLE.
Call (704-799-2192) or E-Mail Us.
COMING SOON
RACE TECH SHOCK SPRINGS - for OEM Shock
Race Tech HP Springs have a high
stiffness-to-mass ratio. In other words; our springs are light weight
for their particular spring rate. This requires the finest materials and
processing. Shot-peened and pre-set so they cannot sack out. All Race
Tech HP Springs have the highest rate tolerences in the industry. These
are the finest springs in the world-guaranteed. Race Tech OEM Replacement Shock Springs
>>
CRG Carbon Fiber Clutch and Brake Levers ( Shorty or Standard)
<<
KOSO Digital Engine Temperature Gauge
(# BA003245)
Fits: '19-'20 MONKEY 125
Coming soon
Shows Temperature in either
°F or °C
Peak Temperature Recall Function
12 Volts DC
On Sale $89.95
SBL LUGGAGE RACK
SALE PRICE - $88.99
Each Year, , when the “ALL NEW”
models are released it takes anywhere from
2 weeks up
to 4 months for new parts to get released to the public.
The Parts Manufacturer’s
have to get the bikes, make the prototypes. Test the protype.
If it works correctly, then they Manufacturer volumes, and then get them to the
dealers.
This takes time. It’s just part of life.
Meanwhile, customers like yourself, are anxiously waiting to get the newest
and coolest products… NOW.
And each year, many of you will wait until the product
is released to order it.
But, by the time the product is released, the demand far exceeds the supply.
Meaning 100
customers want Product X, but only 30
units arrive in the first shipment to the U.S. So, that means 70 customers have to wait another 2-4 weeks
for more product to become available.
Because Soo many others have already placed their orders, you have to wait
even longer to get yours.
Well, there is a way to fix that.
This
year we are encouraging our customers to order early.
There is absolutely, NO RISK. NON AT ALL.
We will NOT Charge your credit card until the product is ready to ship
to you. PERIOD.
NO Deposit, NO Cancellation Fee’s, NO BS.
And you may cancel your
order at anytime. We have no problem with that.
The demand for these new parts is soo high, if you cancel, we just go down the
list,
and make the next customer the happiest man in town.
So, you have Nothing to
lose… and soo much to gain.
The sooner you put your
order in for a new part, the higher up on the list you get.
That way, when the new part gets released, you get first dibbs over everyone
else.
It doesn’t matter if there is a price yet or a even a
part number.
Just tell us what bike, and what part, and Your Order is LOCKED.
PERIOD. It's that easy.
We will call you the day the part is ready to ship, and give you final decision
if you still want it.
If you say “YES”…. we will ship it immediately.
If you say “NO”, we will cancel the order and move down the list to the next
customer.
NOTHING TO LOSE……… Yet Soo much to gain.
Don’t wait till the last
minute. If you have a part you want to order, CALL US
now or >Order On-Line<
ONE MORE TIME….. DON’T WAIT.
You know the saying, “You snooze, You lose”.
** Please note,
the No cancellation fee ONLY applies to "ALL NEW" Parts that have not been
released yet.
It does NOT apply to
"Special Order Parts" that have already been released to the public and are no
longer in demand.
<<
&
Facebook: Click
>>
<< to become a Fan or Friend. 
<<
DYNO >> 
$105.95
